WiFi Component

This core esphomelib component sets up WiFi connections to access points for you. It needs to be in your configuration or otherwise esphomeyaml will fail in the config validation stage.

It’s recommended to provide a static IP for your node, as it can dramatically improve connection times.

# Example configuration entry
wifi:
  ssid: MyHomeNetwork
  password: VerySafePassword

  # Optional manual IP
  manual_ip:
    static_ip: 10.0.0.42
    gateway: 10.0.0.1
    subnet: 255.255.255.0

Configuration variables:

  • ssid (Optional, string): The name (or service set identifier) of the WiFi access point your device should connect to.
  • password (Optional, string): The password (or PSK) for your WiFi network. Leave empty for no password.
  • manual_ip (Optional): Manually configure the static IP of the node.
    • static_ip (Required, IPv4 address): The static IP of your node.
    • gateway (Required, IPv4 address): The gateway of the local network.
    • subnet (Required, IPv4 address): The subnet of the local network.
    • dns1 (Optional, IPv4 address): The main DNS server to use.
    • dns2 (Optional, IPv4 address): The backup DNS server to use.
  • hostname (Optional, string): Manually set the hostname of the node. Can only be 63 long at max and must only contain alphanumeric characters plus dashes and underscores.
  • ap (Optional): Enable an access point mode on the node.
    • ssid (Required, string): The name of the access point to create.
    • password (Optional string): The password for the access point. Leave empty for no password.
    • channel (Optional, int): The channel the AP should operate on from 1 to 14. Defaults to 1.
    • manual_ip (Optional): Manually set the IP options for the AP. Same options as manual_ip for station mode.
  • domain (Optional, string): Set the domain of the node hostname used for uploading. For example, if it’s set to .local, all uploads will be sent to <HOSTNAME>.local. Defaults to .local.
  • reboot_timeout (Optional, time): The amount of time to wait before rebooting when no WiFi connection exists. Can be disabled by setting this to 0s, but note that the low level IP stack currently seems to have issues with WiFi where a full reboot is required to get the interface back working. Defaults to 5min.
  • power_save_mode (Optional, string): The power save mode for the WiFi interface. Defaults to no power saving. See Power Save Mode
  • id (Optional, ID): Manually specify the ID used for code generation.

Access Point Mode

Since version 1.3, esphomelib has an optional “Access Point Mode”. If you include ap: in your wifi configuration, esphomelib will automatically set up an access point that you can connect to. Additionally, you can specify both a “normal” station mode and AP mode at the same time. This will cause esphomelib to only enable the access point when no connection to the wifi router can be made.

Manual IPs

If you’re having problems with your node not connecting to WiFi or the connection process taking a long time, it can be a good idea to assign a static IP address to the ESP. This way, the ESP doesn’t need to go through the slow DHCP process.

You can do so with the manual_ip: option in the WiFi configuration.

wifi:
  # ...
  manual_ip:
    # Set this to the IP of the ESP
    static_ip: 10.0.0.42
    # Set this to the IP address of the router. Often ends with .1
    gateway: 10.0.0.1
    # The subnet of the network. 255.255.255.0 works for most home networks.
    subnet: 255.255.255.0

After putting a manual IP in your configuration, the ESP will no longer need to negotiate a dynamic IP address with the router, thus improving the time until connection.

Additionally, this can help with Over-The-Air updates if for example the home network doesn’t allow for .local addresses. When a manual IP is in your configuration, the OTA process will automatically choose that as the target for the upload.

Power Save Mode

The WiFi interface of all ESPs offer three power save modes to reduce the amount of power spent on WiFi. While some options can reduce the power usage of the ESP, they generally also decrease the reliability of the WiFi connection, with frequent disconnections from the router in the highest power saving mode.

The default is none (a bit of power saving). If you experience frequent WiFi disconnection problems, please also try light.

  • NONE (least power saving, Default)
  • LIGHT
  • HIGH (most power saving)
wifi:
  # ...
  power_save_mode: none