Ethernet Component

This ESPHome component enables wired Ethernet connections for ESP32s.

Ethernet for ESP8266 is not supported.

This component and the Wi-Fi component may not be used simultaneously, even if both are physically available.

# Example configuration entry for RMII chips
ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_IN
  phy_addr: 0

  # Optional manual IP
  manual_ip:
    static_ip: 10.0.0.42
    gateway: 10.0.0.1
    subnet: 255.255.255.0

# Example configuration entry for SPI chips
ethernet:
  type: W5500
  clk_pin: GPIO19
  mosi_pin: GPIO21
  miso_pin: GPIO23
  cs_pin: GPIO18
  interrupt_pin: GPIO36
  reset_pin: GPIO22

Configuration variables:

  • type (Required, string): The type of LAN chipset/phy.

    Supported chipsets are:

    • LAN8720 (RMII)

    • RTL8201 (RMII)

    • DP83848 (RMII)

    • IP101 (RMII)

    • JL1101 (RMII)

    • KSZ8081 (RMII)

    • KSZ8081RNA (RMII)

    • W5500 (SPI)

RMII configuration variables:

  • mdc_pin (Required, Pin): The MDC pin of the board. Usually this is GPIO23.

  • mdio_pin (Required, Pin): The MDIO pin of the board. Usually this is GPIO18.

  • clk_mode (Optional, string): The clock mode of the data lines. See your board’s datasheet for more details. Must be one of the following values:

    • GPIO0_IN (Default) - External clock

    • GPIO0_OUT - Internal clock

    • GPIO16_OUT - Internal clock

    • GPIO17_OUT - Internal clock

  • phy_addr (Optional, int): The PHY addr type of the Ethernet controller. Defaults to 0.

  • power_pin (Optional, Pin Schema): The pin controlling the power/reset status of the Ethernet controller. Leave unspecified for no power pin (default).

SPI configuration variables:

  • clk_pin (Required, Pin): The SPI clock pin.

  • mosi_pin (Required, Pin): The SPI MOSI pin.

  • miso_pin (Required, Pin): The SPI MISO pin.

  • cs_pin (Required, Pin): The SPI chip select pin.

  • interrupt_pin (Optional, Pin): The interrupt pin.

  • reset_pin (Optional, Pin): The reset pin.

  • clock_speed (Optional, float): The SPI clock speed. Any frequency between 8Mhz and 80Mhz is allowed, but the nearest integer division of 80Mhz is used, i.e. 16Mhz (80Mhz / 5) is used when 15Mhz is configured. Default: 26.67Mhz.

Advanced common configuration variables:

  • manual_ip (Optional): Manually configure the static IP of the node.

    • static_ip (Required, IPv4 address): The static IP of your node.

    • gateway (Required, IPv4 address): The gateway of the local network.

    • subnet (Required, IPv4 address): The subnet of the local network.

    • dns1 (Optional, IPv4 address): The main DNS server to use.

    • dns2 (Optional, IPv4 address): The backup DNS server to use.

  • use_address (Optional, string): Manually override what address to use to connect to the ESP. Defaults to auto-generated value. For example, if you have changed your static IP and want to flash OTA to the previously configured IP address.

  • domain (Optional, string): Set the domain of the node hostname used for uploading. For example, if it’s set to .local, all uploads will be sent to <HOSTNAME>.local. Defaults to .local.

  • id (Optional, ID): Manually specify the ID used for code generation.

Note

If your Ethernet board is not designed with an ESP32 built in, it’s common to attempt to use flying leads, dupont wires, etc. to connect the Ethernet controller to the ESP32. This approach is likely to fail, however, as the Ethernet interface uses a high frequency clock signal that will not travel reliably over these types of connections. For more information and wiring details refer to the link in the See also section.

Note

SPI based chips do not use SPI Bus. This means that SPI pins can’t be shared with other devices.

Configuration examples

Olimex ESP32-POE:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 0
  power_pin: GPIO12

Note

WROVER version of Olimex POE cards change CLK to ping GPIO0, configuration must be clk_mode: GPIO0_OUT.

Olimex ESP32-EVB:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_IN
  phy_addr: 0

Olimex ESP32-GATEWAY and LILYGO TTGO T-Internet-POE ESP32-WROOM LAN8270A:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 0

LILYGO TTGO T-Internet ESP32-WROVER-E LAN8270:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_OUT
  phy_addr: 0
  power_pin: GPIO04

Wireless Tag WT32-ETH01 and SMLIGHT SLZB-06 PoE Zigbee:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_IN
  phy_addr: 1
  power_pin: GPIO16

M5Stack PoESP32 and ESP32-Ethernet-Kit:

ethernet:
  type: IP101
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_IN
  phy_addr: 1
  power_pin: GPIO5

AiThinker ESP32-G Gateway:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 1
  power_pin: GPIO5

wESP32:

# for board up to rev.5
ethernet:
  type: LAN8720
  mdc_pin: GPIO16
  mdio_pin: GPIO17
  clk_mode: GPIO0_IN
  phy_addr: 0

# for board rev.7 and up
ethernet:
  type: RTL8201
  mdc_pin: GPIO16
  mdio_pin: GPIO17
  clk_mode: GPIO0_IN
  phy_addr: 0

Note

Revision 5 and below of the wESP32 board use the LAN8720 Ethernet PHY. Revision 7 and newer of it use the RTL8201 Ethernet PHY. Support for RTL8201 is available from ESPHome version 2022.12 upwards.

OpenHacks LAN8720:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  phy_addr: 1

Note

This board has an issue that might cause the ESP32 to boot in program mode. When testing, make sure you are monitoring the serial output and reboot the device several times to see if it boots into the program properly.

Esp32-Stick-Eth and Esp32-Stick-PoE-P and Esp32-Stick-PoE-A:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 1

LILYGO T-ETH-Lite ESP32:

ethernet:
  type: RTL8201
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_IN
  phy_addr: 0
  power_pin: GPIO12

See Also